radiomaster-pocket-dat.md
DML setup
setup page 2
SYS setup
navigate to hardware page
Navigating to the H/W Page
Press and hold or simply press the SYS button to open the system settings.
Look at the very top right corner of your screen. You will see page tracking numbers like 1/7, 2/7, etc.
Press the PAGE> button repeatedly until you hitpage 6/7 (or 7/7 depending on your exact version).
Look at the top text label—it will say H/W. This is your Hardware page!
check version
Press the PAGE< button to 7/7
change baud rate
Step 2: Unlocking your Baud Rate
- Once you are on the H/W page, scroll all the way down until you see Internal RF.
- Right below where it says
Type: CRSF, you should now see Baudrate. - Change it from
400kdown to115k. - Turn your radio off and back on again to save the changes.
⚠️ One Final Reminder: Now that your radio is outputting at 115,200 bps, you must open your ExpressLRS LUA script (Short press SYS $\rightarrow$ ExpressLRS) and drop your Packet Rate down to 50Hz or 100Hz. If you leave it at 250Hz or 500Hz, the 115,200 baud wire speed will instantly bottleneck and cause sensor errors.
bootloader mode
Bootloader: Turn off the radio transmitter. Push both trim hat switches inward together and press the power button.
DFU: Turn off the radio transmitter. Plug in the USB cable to the USB port on the top of the radio. - STM32-DFU-dat - STM32-dat
Enter Bootloader Mode: Turn your RadioMaster Pocket completely OFF. Hold both horizontal trim buttons (T1 and T4) inward toward the power button while pressing the power button. The screen will say "EdgeTX Bootloader".
In the context of the RadioMaster Pocket, T1 and T4 refer to the horizontal trim switches situated directly below the gimbals. T1 corresponds to your Roll (Aileron) trim, while T4 corresponds to your Yaw (Rudder) trim.
version pocket
all buttons
Default Stick Assignments
RC template
| Input | Type | default | modify |
|---|---|---|---|
| CH1 | Stick | Roll | |
| CH2 | Stick | Pitch | |
| CH3 | Stick | Yaw | |
| CH4 | Stick | Throttle | |
| SA | 2-pos | Arm/Aux | |
| SB | 3-pos | Mode/Aux | |
| SC | 3-pos | Mode/Aux | |
| SD | Self-lock | Aux | |
| SE | Momentary | Beep/Aux | |
| S1 | Knob | Trim/Aux |
| Channel | Function |
|---|---|
| CH1 | Roll (Aileron) |
| CH2 | Pitch (Elevator) |
| CH3 | Yaw (Rudder) |
| CH4 | Throttle |
| Switch / Knob | Type | Typical Use |
|---|---|---|
| SA | 2-position switch | Arming, auxiliary control |
| SB | 3-position switch | Flight modes, auxiliary control |
| SC | 3-position switch | Flight modes, auxiliary control |
| SD | 2-position self-locking switch | Auxiliary function |
| SE | Momentary (spring-loaded) | Beeper, auxiliary function |
| S1 | Rotary potentiometer | Auxiliary function, trims |
1. Radiomaster Pocket (Multi-Protocol Version)
- Uses CC2500 module, same chip used in FrSky radios.
- Supports FrSky D8, D16, Futaba SFHSS, Hubsan, and many more protocols.
- ✅ You can bind directly to FrSky D8 receivers.
2. Radiomaster Pocket (ELRS Version)
- Uses ExpressLRS only.
- ❌ Does NOT support FrSky D8/D16.
- You would need to use an external CC2500 module if you want D8.