[32]HELLO! BOOT0 is starting!
[35]BOOT0 commit : adaf1174cc
[38]set pll start
[40]periph0 has been enabled
[42]set pll end
[44][pmu]: bus read error
[46]board init ok
[48]ZQ value = 0x2d
[50]get_pmu_exist() = -1
[52]ddr_efuse_type: 0xa
[55]trefi:7.8ms
[57][AUTO DEBUG] single rank and full DQ!
[61]ddr_efuse_type: 0xa
[63]trefi:7.8ms
[65][AUTO DEBUG] rank 0 row = 13
[68][AUTO DEBUG] rank 0 bank = 4
[71][AUTO DEBUG] rank 0 page size = 2 KB
[75]DRAM BOOT DRIVE INFO: V0.33
[78]DRAM CLK = 528 MHz
[80]DRAM Type = 2 (2:DDR2,3:DDR3)
[83]DRAMC read ODT off.
[85]DRAM ODT off.
[87]ddr_efuse_type: 0xa
[90]DRAM SIZE =64 M
[91]dram_tpr4:0x0
[93]PLL_DDR_CTRL_REG:0xf8002b00
[96]DRAM_CLK_REG:0xc0000000
[99][TIMING DEBUG] MR2= 0x0
[103]DRAM simple test OK.
[105]dram size =64
[107]card no is 0
[109]sdcard 0 line count 4
[111][mmc]: mmc driver ver 2021-04-2 16:45
[121][mmc]: Wrong media type 0x0
[124][mmc]: ***Try SD card 0***
[133][mmc]: HSSDR52/SDR25 4 bit
[136][mmc]: 50000000 Hz
[138][mmc]: 15343 MB
[140][mmc]: ***SD/MMC 0 init OK!!!***
[191]Loading boot-pkg Succeed(index=0).
[194]Entry_name = opensbi
[198]Entry_name = u-boot
[201]Entry_name = dtb
[204]mmc not para
[206]Jump to second Boot.
OpenSBI auto-t113-linux-V0.8-1-g771d82e
____ _____ ____ _____
/ __ \ / ____| _ \_ _|
| | | |_ __ ___ _ __ | (___ | |_) || |
| | | | '_ \ / _ \ '_ \ \___ \| _ < | |
| |__| | |_) | __/ | | |____) | |_) || |_
\____/| .__/ \___|_| |_|_____/|____/_____|
| |
|_|
Platform Name : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs : 1
Current Hart : 0
Firmware Base : 0x41fc0400
Firmware Size : 75 KB
Runtime SBI Version : 0.2
MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0 : 0x0000000041fc0000-0x0000000041fdffff (A)
PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3 : 0x0000000000020000-0x0000000000027fff (A,ÿ
U-Boot 2018.05-g2a1965a (Jul 10 2022 - 02:50:57 +0000) Allwinner Technology
[00.291]DRAM: 64 MiB
[00.293]Relocation Offset is: 01ed9000
[00.297]secure enable bit: 0
[00.300]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
[00.306]flash init start
[00.308]workmode = 0,storage type = 1
[00.312][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[00.317][mmc]: get sdc_type fail and use default host:tm1.
[00.324][mmc]: can't find node "mmc0",will add new node
[00.328][mmc]: fdt err returned <no error>
[00.332][mmc]: Using default timing para
[00.336][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.354][mmc]: card_caps:0x3000000a
[00.357][mmc]: host_caps:0x3000003f
[00.360]sunxi flash init ok
[00.363]line:703 init_clocks
[00.366]drv_disp_init
request pwm success, pwm7:pwm7:0x2000c00.
fdt get node offset faill: hdmi
[00.384]unable to map hdmi registers
[00.387]drv_disp_init finish
[00.404]Loading Environment from SUNXI_FLASH... OK
[00.425]boot_gui_init:start
[00.428]set disp.dev2_output_type fail. using defval=0
[00.435]boot_gui_init:finish
partno erro : can't find partition bootloader
54 bytes read in 1 ms (52.7 KiB/s)
[00.449]bmp_name=bootlogo.bmp size 28854
28854 bytes read in 19 ms (1.4 MiB/s)
[00.478]out of usb burn from boot: not need burn key
[00.483]Item0 (Map) magic is bad
[00.486]the secure storage item0 copy0 magic is bad
[00.491]Item0 (Map) magic is bad
[00.494]the secure storage item0 copy1 magic is bad
[00.499]Item0 (Map) magic is bad
List file under ULI/factory
** Unrecognized filesystem type **
root_partition is rootfs
set root to /dev/mmcblk0p5
[00.514]update part info
[00.518]update bootcmd
[00.522]change working_fdt 0x42a98da0 to 0x42a78da0
disable nand error: FDT_ERR_BADPATH
[00.531]The storage not support sample function
No reserved memory region found in source FDT
[00.556]update dts
noncached_alloc(): addr = 0x42b02a40
noncached_alloc(): addr = 0x42b02a80
noncached_alloc(): addr = 0x42b02ac0
noncached_alloc(): addr = 0x42b03300
geth_sys_init:639: get node 'gmac0' error
geth_sys_init fail!
[00.577]Board Net Initialization Failed
[00.580]No ethernet found.
Hit any key to stop autoboot: 1 FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL
sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1
[00.625]LCD open finish
0
[01.882]no vendor_boot partition is found
Android's image name: f133-mq_r
Detect comp none
[01.898]
Starting kernel ...
[01.901][mmc]: MMC Device 2 not found
[01.905][mmc]: mmc 2 not find, so not exit
[ 0.000000] Linux version 5.4.61 (test@test-virtual-machine) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #2 PREEMPT Tue May 2 06:32:35 UTC 2023
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000040000000-0x0000000043ffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000043ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x0000000043ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] DMA32 zone: 224 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 16384 pages, LIFO batch:3
[ 0.000000] elf_hwcap is 0x20112d
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16160
[ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/pseudo_init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:rootfs_data@mmcblk0p7:UDISK@mmcblk0p8 cma=0M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun20iw1p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-g2a1965a(07/10/2022-02:50:57) mbr_o
[ 0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.000000] Sorting __ex_table...
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 55896K/65536K available (4123K kernel code, 405K rwdata, 1699K rodata, 136K init, 229K bss, 9640K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts.
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000027] riscv_timer_clockevent depends on broadcast, but no broadcast function available
[ 0.000361] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000947] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000968] pid_max: default: 32768 minimum: 301
[ 0.001127] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.001147] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.002817] ASID allocator initialised with 65536 entries
[ 0.002985] rcu: Hierarchical SRCU implementation.
[ 0.003645] devtmpfs: initialized
[ 0.019187] random: get_random_u32 called from bucket_table_alloc.isra.27+0x102/0x124 with crng_init=0
[ 0.020051] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.020136] futex hash table entries: 256 (order: 0, 6144 bytes, linear)
[ 0.020282] pinctrl core: initialized pinctrl subsystem
[ 0.021646] NET: Registered protocol family 16
[ 0.022409] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.023075] cpuidle: using governor menu
[ 0.065986] rtc_ccu: sunxi ccu init OK
[ 0.074358] clock: sunxi ccu init OK
[ 0.076207] clock: sunxi ccu init OK
[ 0.106479] iommu: Default domain type: Translated
[ 0.106671] sunxi iommu: irq = 4
[ 0.107895] SCSI subsystem initialized
[ 0.108147] usbcore: registered new interface driver usbfs
[ 0.108240] usbcore: registered new interface driver hub
[ 0.108356] usbcore: registered new device driver usb
[ 0.109357] Advanced Linux Sound Architecture Driver Initialized.
[ 0.110341] pwm module init!
[ 0.112130] g2d 5410000.g2d: Adding to iommu group 0
[ 0.112659] G2D: rcq version initialized.major:252
[ 0.113669] clocksource: Switched to clocksource riscv_clocksource
[ 0.127223] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[ 0.130584] NET: Registered protocol family 2
[ 0.131469] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.131512] TCP established hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.131534] TCP bind hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.131548] TCP: Hash tables configured (established 512 bind 512)
[ 0.131696] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.131742] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.131974] NET: Registered protocol family 1
[ 0.133142] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[ 0.133848] spi spi0: spi0 supply spi not found, using dummy regulator
[ 0.134130] sunxi_spi_resource_get()2116 - [spi0] SPI MASTER MODE
[ 0.134192] sunxi_spi_resource_get()2154 - Failed to get sample mode
[ 0.134203] sunxi_spi_resource_get()2159 - Failed to get sample delay
[ 0.134214] sunxi_spi_resource_get()2163 - sample_mode:-1431633921 sample_delay:-1431633921
[ 0.134279] sunxi_spi_clk_init()2205 - [spi0] mclk 100000000
[ 0.135104] sunxi_spi_probe()2623 - [spi0]: driver probe succeed, base ffffffd004058000, irq 31
[ 0.137212] workingset: timestamp_bits=62 max_order=14 bucket_order=0
[ 0.145805] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.146050] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.146381] fuse: init (API version 7.31)
[ 0.167788] io scheduler mq-deadline registered
[ 0.167805] io scheduler kyber registered
[ 0.168708] [DISP]disp_module_init
[ 0.169333] disp 5000000.disp: Adding to iommu group 0
[ 0.169884] [DISP] parser_disp_init_para,line:1430:
[ 0.169889] of_property_read fb0_width fail
[ 0.169911] [DISP] disp_init,line:2386:
[ 0.169915] smooth display screen:0 type:1 mode:4
[ 0.210704] display_fb_request,fb_id:0
[ 0.219072] Freeing logo buffer memory: 1500K
[ 0.219594] disp_al_manager_apply ouput_type:1
[ 0.220023] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[ 0.220808] [DISP]disp_module_init finish
[ 0.221700] sunxi_sid_init()551 - insmod ok
[ 0.222296] pwm-regulator: supplied by regulator-dummy
[ 0.224054] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[ 0.224538] uart uart0: uart0 supply uart not found, using dummy regulator
[ 0.224930] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI
[ 0.224958] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n
[ 0.943314] printk: console [ttyS0] enabled
[ 0.949217] misc dump reg init
[ 0.953736] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[ 0.965027] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[ 0.972243] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[ 0.979639] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[ 0.987062] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[ 0.993594] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[ 1.000552] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1)
[ 1.008358] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1
[ 1.016247] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[ 1.024389] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[ 1.032096] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[ 1.038871] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1)
[ 1.046472] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0
[ 1.054697] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11
[ 1.062397] [ADDR_MGT] addr_mgt_probe: success.
[ 1.068483] sunxi-spinand: AW SPINand MTD Layer Version: 2.3 20211223
[ 1.075810] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306
[ 1.086619] random: fast init done
[ 1.284341] random: crng init done
[ 2.073747] sunxi-spinand-phy: read id failed : -110
[ 2.079316] spi-nand: probe of spi0.0 failed with error -110
[ 2.085807] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.093089] sunxi-ehci: EHCI SUNXI driver
[ 2.098062] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.105090] sunxi-ohci: OHCI SUNXI driver
[ 2.112178] sunxi-rtc 7090000.rtc: registered as rtc0
[ 2.118048] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:21 UTC (21)
[ 2.127044] sunxi-rtc 7090000.rtc: sunxi rtc probed
[ 2.133047] i2c /dev entries driver
[ 2.137049] sunxi cedar version 1.1
[ 2.141227] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[ 2.147532] VE: install start!!!
[ 2.147532]
[ 2.153114] VE: cedar-ve the get irq is 6
[ 2.153114]
[ 2.159496] VE: ve_debug_proc_info:00000000f36217e6, data:00000000dc0b564d, lock:00000000c9928603
[ 2.159496]
[ 2.171135] VE: install end!!!
[ 2.171135]
[ 2.176213] VE: sunxi_cedar_probe
[ 2.180880] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 2.192331] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40)
[ 2.202403] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[ 2.208636] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[ 2.214972] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[ 2.221410] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[ 2.227844] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[ 2.234413] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[ 2.240918] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[ 2.247452] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[ 2.254497] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[ 2.259842] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
[ 2.266531] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.277729] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[ 2.297920] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.322389] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
[ 2.322460] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 2.339973] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40)
[ 2.350011] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[ 2.356403] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[ 2.362761] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[ 2.369255] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[ 2.375687] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[ 2.382189] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[ 2.388749] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[ 2.395280] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[ 2.401863] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[ 2.411334] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.422536] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[ 2.442694] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.466946] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[ 2.474658] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 2.481767] ashmem: initialized
[ 2.485295] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 2.492229] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.503844] exFAT: Version 1.3.0
[ 2.511958] [AUDIOCODEC][sunxi_codec_parse_params][2412]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1
[ 2.511958]
[ 2.529288] [AUDIOCODEC][sunxi_codec_parse_params][2448]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[ 2.540874] [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished
[ 2.549134] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.562143] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[ 2.572145] [SNDCODEC][sunxi_card_init][583]:card init finished
[ 2.579640] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 2.587275] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 2.594861] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 2.601807] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[ 2.611615] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 2.618428] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 2.631090] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0
[ 2.643523] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished
[ 2.653163] NET: Registered protocol family 10
[ 2.658258] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch
[ 2.667015] Segment Routing with IPv6
[ 2.671338] NET: Registered protocol family 17
[ 2.697764] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator
[ 2.712526] sunxi-i2c sunxi-i2c2: probe success
[ 2.720000] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[ 2.734084] get ehci0-controller wakeup-source is fail.
[ 2.740050] sunxi ehci0-controller don't init wakeup source
[ 2.746322] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe000661b28, 0x:ffffffd0040f1000, irq_no:2e
[ 2.759871] [sunxi-ehci0]: Not init ehci0
[ 2.764901] get ohci0-controller wakeup-source is fail.
[ 2.770904] sunxi ohci0-controller don't init wakeup source
[ 2.777174] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe000661ef0
[ 2.787649] [sunxi-ohci0]: Not init ohci0
[ 2.792655] get ehci1-controller wakeup-source is fail.
[ 2.798643] sunxi ehci1-controller don't init wakeup source
[ 2.804975] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe0006622b8, 0x:ffffffd0040fb000, irq_no:31
[ 2.818819] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[ 2.832493] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[ 2.839819] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[ 2.849685] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000
[ 2.883725] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[ 2.892631] hub 1-0:1.0: USB hub found
[ 2.896950] hub 1-0:1.0: 1 port detected
[ 2.902503] get ohci1-controller wakeup-source is fail.
[ 2.908576] sunxi ohci1-controller don't init wakeup source
[ 2.914865] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe000662680
[ 2.925618] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[ 2.938083] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[ 2.945418] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[ 2.955262] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400
[ 3.028775] hub 2-0:1.0: USB hub found
[ 3.033013] hub 2-0:1.0: 1 port detected
[ 3.040483] get usb_detect_mode is fail, -22
[ 3.045369] get det_vbus is fail, -84
[ 3.049451] get id is fail, -84
[ 3.055469] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 3.065199] clk: Not disabling unused clocks
[ 3.069966] ALSA device list:
[ 3.073320] #0: audiocodec
[ 3.076619] cfg80211: failed to load regulatory.db
[ 3.082023] alloc_fd: slot 0 not NULL!
[ 3.086691] VFS: Cannot open root device "mmcblk0p5" or unknown-block(0,0): error -6
[ 3.095459] Please append a correct "root=" boot option; here are the available partitions:
[ 3.104843] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 3.114063] CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.61 #2
[ 3.120464] Call Trace:
[ 3.123206] [<ffffffe000023d56>] walk_stackframe+0x0/0x70
[ 3.129230] [<ffffffe000027d2c>] panic+0xdc/0x266
[ 3.134478] [<ffffffe000000d9c>] mount_block_root+0x1fe/0x266
[ 3.140888] [<ffffffe000000fc2>] prepare_namespace+0x136/0x144
[ 3.147392] [<ffffffe0004242a2>] rest_init+0xbc/0xc0
[ 3.152925] [<ffffffe0004242b0>] kernel_init+0xa/0xe8
[ 3.158554] [<ffffffe0004242a2>] rest_init+0xbc/0xc0
[ 3.164087] [<ffffffe000022d5c>] ret_from_syscall+0xa/0xe
[ 3.170114] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---