[32]HELLO! BOOT0 is starting!
[35]BOOT0 commit : adaf1174cc
[38]set pll start
[40]periph0 has been enabled
[43]set pll end
[44][pmu]: bus read error
[46]board init ok
[48]ZQ value = 0x31
[50]get_pmu_exist() = -1
[53]ddr_efuse_type: 0xa
[55]trefi:7.8ms
[57][AUTO DEBUG] single rank and full DQ!
[61]ddr_efuse_type: 0xa
[63]trefi:7.8ms
[65][AUTO DEBUG] rank 0 row = 13
[68][AUTO DEBUG] rank 0 bank = 4
[71][AUTO DEBUG] rank 0 page size = 2 KB
[75]DRAM BOOT DRIVE INFO: V0.33
[78]DRAM CLK = 528 MHz
[80]DRAM Type = 2 (2:DDR2,3:DDR3)
[83]DRAMC read ODT off.
[85]DRAM ODT off.
[87]ddr_efuse_type: 0xa
[90]DRAM SIZE =64 M
[92]dram_tpr4:0x0
[93]PLL_DDR_CTRL_REG:0xf8002b00
[96]DRAM_CLK_REG:0xc0000000
[99][TIMING DEBUG] MR2= 0x0
[103]DRAM simple test OK.
[106]dram size =64
[107]card no is 0
[109]sdcard 0 line count 4
[112][mmc]: mmc driver ver 2021-04-2 16:45
[121][mmc]: Wrong media type 0x0
[124][mmc]: ***Try SD card 0***
[133][mmc]: HSSDR52/SDR25 4 bit
[136][mmc]: 50000000 Hz
[138][mmc]: 15343 MB
[140][mmc]: ***SD/MMC 0 init OK!!!***
[191]Loading boot-pkg Succeed(index=0).
[194]Entry_name = opensbi
[198]Entry_name = u-boot
[201]Entry_name = dtb
[204]mmc not para
[206]Jump to second Boot.
OpenSBI auto-t113-linux-V0.8-1-g771d82e
____ _____ ____ _____
/ __ \ / ____| _ \_ _|
| | | |_ __ ___ _ __ | (___ | |_) || |
| | | | '_ \ / _ \ '_ \ \___ \| _ < | |
| |__| | |_) | __/ | | |____) | |_) || |_
\____/| .__/ \___|_| |_|_____/|____/_____|
| |
|_|
Platform Name : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs : 1
Current Hart : 0
Firmware Base : 0x41fc0400
Firmware Size : 75 KB
Runtime SBI Version : 0.2
MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0 : 0x0000000041fc0000-0x0000000041fdffff (A)
PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3 : 0x0000000000020000-0x0000000000027fff (A,
U-Boot 2018.05-g2a1965a (Jul 10 2022 - 02:50:57 +0000) Allwinner Technology
[00.291]DRAM: 64 MiB
[00.293]Relocation Offset is: 01ed9000
[00.297]secure enable bit: 0
[00.300]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
[00.306]flash init start
[00.308]workmode = 0,storage type = 1
[00.312][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[00.317][mmc]: get sdc_type fail and use default host:tm1.
[00.324][mmc]: can't find node "mmc0",will add new node
[00.328][mmc]: fdt err returned <no error>
[00.332][mmc]: Using default timing para
[00.336][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.354][mmc]: card_caps:0x3000000a
[00.357][mmc]: host_caps:0x3000003f
[00.360]sunxi flash init ok
[00.363]line:703 init_clocks
[00.366]drv_disp_init
request pwm success, pwm7:pwm7:0x2000c00.
fdt get node offset faill: hdmi
[00.384]unable to map hdmi registers
[00.387]drv_disp_init finish
[00.404]Loading Environment from SUNXI_FLASH... OK
[00.425]boot_gui_init:start
[00.428]set disp.dev2_output_type fail. using defval=0
[00.435]boot_gui_init:finish
partno erro : can't find partition bootloader
54 bytes read in 1 ms (52.7 KiB/s)
[00.448]bmp_name=bootlogo.bmp size 28854
28854 bytes read in 20 ms (1.4 MiB/s)
[00.478]out of usb burn from boot: not need burn key
[00.483]Item0 (Map) magic is bad
[00.486]the secure storage item0 copy0 magic is bad
[00.491]Item0 (Map) magic is bad
[00.494]the secure storage item0 copy1 magic is bad
[00.499]Item0 (Map) magic is bad
List file under ULI/factory
** Unrecognized filesystem type **
root_partition is rootfs
set root to /dev/mmcblk0p5
[00.513]update part info
[00.517]update bootcmd
[00.522]change working_fdt 0x42a98da0 to 0x42a78da0
disable nand error: FDT_ERR_BADPATH
[00.531]The storage not support sample function
No reserved memory region found in source FDT
[00.556]update dts
noncached_alloc(): addr = 0x42b02a40
noncached_alloc(): addr = 0x42b02a80
noncached_alloc(): addr = 0x42b02ac0
noncached_alloc(): addr = 0x42b03300
geth_sys_init:639: get node 'gmac0' error
geth_sys_init fail!
[00.576]Board Net Initialization Failed
[00.580]No ethernet found.
Hit any key to stop autoboot: 1 FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL
sunxi_pwm_pin_set_state, fdt_set_all_pin, ret=-1
[00.625]LCD open finish
0
[01.882]no vendor_boot partition is found
Android's image name: f133-mq_r
Detect comp none
[01.898]
Starting kernel ...
[01.901][mmc]: MMC Device 2 not found
[01.905][mmc]: mmc 2 not find, so not exit
[ 0.000000] Linux version 5.4.61 (test@test-virtual-machine) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #2 PREEMPT Tue May 2 06:32:35 UTC 2023
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000040000000-0x0000000043ffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000043ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x0000000043ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] DMA32 zone: 224 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 16384 pages, LIFO batch:3
[ 0.000000] elf_hwcap is 0x20112d
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16160
[ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/pseudo_init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:rootfs_data@mmcblk0p7:UDISK@mmcblk0p8 cma=0M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun20iw1p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-g2a1965a(07/10/2022-02:50:57) mbr_o
[ 0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.000000] Sorting __ex_table...
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 55896K/65536K available (4123K kernel code, 405K rwdata, 1699K rodata, 136K init, 229K bss, 9640K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts.
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000027] riscv_timer_clockevent depends on broadcast, but no broadcast function available
[ 0.000365] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000940] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000962] pid_max: default: 32768 minimum: 301
[ 0.001123] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.001142] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.002829] ASID allocator initialised with 65536 entries
[ 0.003000] rcu: Hierarchical SRCU implementation.
[ 0.003670] devtmpfs: initialized
[ 0.019704] random: get_random_u32 called from bucket_table_alloc.isra.27+0x102/0x124 with crng_init=0
[ 0.020661] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.020690] futex hash table entries: 256 (order: 0, 6144 bytes, linear)
[ 0.020830] pinctrl core: initialized pinctrl subsystem
[ 0.022223] NET: Registered protocol family 16
[ 0.022989] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.023663] cpuidle: using governor menu
[ 0.066933] rtc_ccu: sunxi ccu init OK
[ 0.075469] clock: sunxi ccu init OK
[ 0.077352] clock: sunxi ccu init OK
[ 0.107807] iommu: Default domain type: Translated
[ 0.108001] sunxi iommu: irq = 4
[ 0.109244] SCSI subsystem initialized
[ 0.109497] usbcore: registered new interface driver usbfs
[ 0.109592] usbcore: registered new interface driver hub
[ 0.109709] usbcore: registered new device driver usb
[ 0.110979] Advanced Linux Sound Architecture Driver Initialized.
[ 0.111975] pwm module init!
[ 0.113668] g2d 5410000.g2d: Adding to iommu group 0
[ 0.114193] G2D: rcq version initialized.major:252
[ 0.115215] clocksource: Switched to clocksource riscv_clocksource
[ 0.129104] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[ 0.132498] NET: Registered protocol family 2
[ 0.133391] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.133435] TCP established hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.133456] TCP bind hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.133471] TCP: Hash tables configured (established 512 bind 512)
[ 0.133619] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.133666] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.133897] NET: Registered protocol family 1
[ 0.135067] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[ 0.135789] spi spi0: spi0 supply spi not found, using dummy regulator
[ 0.136063] sunxi_spi_resource_get()2116 - [spi0] SPI MASTER MODE
[ 0.136125] sunxi_spi_resource_get()2154 - Failed to get sample mode
[ 0.136136] sunxi_spi_resource_get()2159 - Failed to get sample delay
[ 0.136146] sunxi_spi_resource_get()2163 - sample_mode:-1431633921 sample_delay:-1431633921
[ 0.136210] sunxi_spi_clk_init()2205 - [spi0] mclk 100000000
[ 0.137048] sunxi_spi_probe()2623 - [spi0]: driver probe succeed, base ffffffd004058000, irq 31
[ 0.139181] workingset: timestamp_bits=62 max_order=14 bucket_order=0
[ 0.147950] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.148208] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.148557] fuse: init (API version 7.31)
[ 0.169851] io scheduler mq-deadline registered
[ 0.169868] io scheduler kyber registered
[ 0.170787] [DISP]disp_module_init
[ 0.171417] disp 5000000.disp: Adding to iommu group 0
[ 0.171973] [DISP] parser_disp_init_para,line:1430:
[ 0.171977] of_property_read fb0_width fail
[ 0.171999] [DISP] disp_init,line:2386:
[ 0.172004] smooth display screen:0 type:1 mode:4
[ 0.213322] display_fb_request,fb_id:0
[ 0.221666] Freeing logo buffer memory: 1500K
[ 0.222198] disp_al_manager_apply ouput_type:1
[ 0.222633] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[ 0.223441] [DISP]disp_module_init finish
[ 0.224359] sunxi_sid_init()551 - insmod ok
[ 0.224974] pwm-regulator: supplied by regulator-dummy
[ 0.226806] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[ 0.227292] uart uart0: uart0 supply uart not found, using dummy regulator
[ 0.227690] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI
[ 0.227718] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n
[ 0.946116] printk: console [ttyS0] enabled
[ 0.952001] misc dump reg init
[ 0.956527] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[ 0.967849] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[ 0.975097] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[ 0.982444] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[ 0.989860] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[ 0.996445] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[ 1.003371] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1)
[ 1.011149] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1
[ 1.019036] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[ 1.027232] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[ 1.034908] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[ 1.041762] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1)
[ 1.049311] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0
[ 1.057527] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11
[ 1.065338] [ADDR_MGT] addr_mgt_probe: success.
[ 1.071384] sunxi-spinand: AW SPINand MTD Layer Version: 2.3 20211223
[ 1.078712] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306
[ 1.089504] random: fast init done
[ 1.286801] random: crng init done
[ 2.085310] sunxi-spinand-phy: read id failed : -110
[ 2.090881] spi-nand: probe of spi0.0 failed with error -110
[ 2.097336] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.104651] sunxi-ehci: EHCI SUNXI driver
[ 2.109628] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.116658] sunxi-ohci: OHCI SUNXI driver
[ 2.122234] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1
[ 2.133413] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[ 2.144372] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[ 2.155136] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[ 2.166510] sunxi-rtc 7090000.rtc: registered as rtc0
[ 2.172178] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[ 2.182804] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:28 UTC (28)
[ 2.191852] sunxi-rtc 7090000.rtc: sunxi rtc probed
[ 2.197850] i2c /dev entries driver
[ 2.201838] sunxi cedar version 1.1
[ 2.206064] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[ 2.212314] VE: install start!!!
[ 2.212314]
[ 2.217960] VE: cedar-ve the get irq is 6
[ 2.217960]
[ 2.224292] VE: ve_debug_proc_info:00000000b4714d51, data:00000000bf5ab713, lock:00000000cc0db6a8
[ 2.224292]
[ 2.235933] VE: install end!!!
[ 2.235933]
[ 2.240983] VE: sunxi_cedar_probe
[ 2.245719] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 2.257176] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40)
[ 2.267261] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[ 2.273444] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[ 2.279802] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[ 2.286282] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[ 2.292689] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[ 2.299225] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[ 2.305788] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[ 2.312292] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[ 2.319344] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[ 2.324688] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
[ 2.331378] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.342579] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[ 2.362746] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.387281] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 2.398403] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
[ 2.404766] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.22 2021-12-20 15:40)
[ 2.414907] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[ 2.421208] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[ 2.427560] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[ 2.433967] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[ 2.440440] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[ 2.446977] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[ 2.453501] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[ 2.460033] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[ 2.466593] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[ 2.476100] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.487302] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[ 2.507432] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.531703] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[ 2.538888] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RE !!
[ 2.545969] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RE !!
[ 2.552755] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.564868] ashmem: initialized
[ 2.568425] exFAT: Version 1.3.0
[ 2.576902] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.588736] [AUDIOCODEC][sunxi_codec_parse_params][2412]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1
[ 2.588736]
[ 2.606064] [AUDIOCODEC][sunxi_codec_parse_params][2448]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[ 2.617293] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RE !!
[ 2.624255] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RE !!
[ 2.630975] [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished
[ 2.639143] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RE !!
[ 2.646141] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RE !!
[ 2.652793] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 2.665097] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[ 2.675088] [SNDCODEC][sunxi_card_init][583]:card init finished
[ 2.684331] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[ 2.695841] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0
[ 2.708175] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished
[ 2.717814] NET: Registered protocol family 10
[ 2.724255] Segment Routing with IPv6
[ 2.728458] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch
[ 2.736029] NET: Registered protocol family 17
[ 2.762397] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator
[ 2.777276] sunxi-i2c sunxi-i2c2: probe success
[ 2.784722] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[ 2.798778] get ehci0-controller wakeup-source is fail.
[ 2.804771] sunxi ehci0-controller don't init wakeup source
[ 2.811047] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe000661b28, 0x:ffffffd0040f1000, irq_no:2e
[ 2.824598] [sunxi-ehci0]: Not init ehci0
[ 2.829632] get ohci0-controller wakeup-source is fail.
[ 2.835626] sunxi ohci0-controller don't init wakeup source
[ 2.841879] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe000661ef0
[ 2.852292] [sunxi-ohci0]: Not init ohci0
[ 2.857351] get ehci1-controller wakeup-source is fail.
[ 2.863287] sunxi ehci1-controller don't init wakeup source
[ 2.869561] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe0006622b8, 0x:ffffffd0040fb000, irq_no:31
[ 2.883450] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[ 2.897097] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[ 2.904329] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[ 2.914258] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000
[ 2.945270] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[ 2.954182] hub 1-0:1.0: USB hub found
[ 2.958539] hub 1-0:1.0: 1 port detected
[ 2.964105] get ohci1-controller wakeup-source is fail.
[ 2.970143] sunxi ohci1-controller don't init wakeup source
[ 2.976481] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe000662680
[ 2.987198] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[ 2.999696] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[ 3.007029] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[ 3.016883] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400
[ 3.090386] hub 2-0:1.0: USB hub found
[ 3.094626] hub 2-0:1.0: 1 port detected
[ 3.102073] get usb_detect_mode is fail, -22
[ 3.107025] get det_vbus is fail, -84
[ 3.111108] get id is fail, -84
[ 3.117155] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 3.126885] clk: Not disabling unused clocks
[ 3.131651] ALSA device list:
[ 3.134956] #0: audiocodec
[ 3.138250] cfg80211: failed to load regulatory.db
[ 3.143682] alloc_fd: slot 0 not NULL!
[ 3.148356] VFS: Cannot open root device "mmcblk0p5" or unknown-block(0,0): error -6
[ 3.157147] Please append a correct "root=" boot option; here are the available partitions:
[ 3.166532] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 3.175754] CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.61 #2
[ 3.182154] Call Trace:
[ 3.184895] [<ffffffe000023d56>] walk_stackframe+0x0/0x70
[ 3.190919] [<ffffffe000027d2c>] panic+0xdc/0x266
[ 3.196168] [<ffffffe000000d9c>] mount_block_root+0x1fe/0x266
[ 3.202578] [<ffffffe000000fc2>] prepare_namespace+0x136/0x144
[ 3.209081] [<ffffffe0004242a2>] rest_init+0xbc/0xc0
[ 3.214613] [<ffffffe0004242b0>] kernel_init+0xa/0xe8
[ 3.220240] [<ffffffe0004242a2>] rest_init+0xbc/0xc0
[ 3.225773] [<ffffffe000022d5c>] ret_from_syscall+0xa/0xe
[ 3.231800] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---