Changes in f5bf627: 1245

				Board-dat/Board-DAT.md
			
          @@ -23,6 +23,8 @@

           ### DAS

           - [[DAS1033-DAT]] - [[DAS1043-DAT]] - [[DAS1087-DAT]]

          +- [[DAS1069-dat]]

          +  

           ### DAR

           - [[DAR1053-DAT]] - [[DAR1064-DAT]] - [[DAR1019-dat]]

				Board-dat/NWI/NWI1245-DAT/NWI1245-DAT.md
			
          @@ -28,10 +28,12 @@ https://www.electrodragon.com/product/esp32-can-rs-485-wire-interface-shield/

           - IO5 = LED

           - general load switching 

          +- please note one chip is not soldering default in case you don't need two to save cost

          +- try IO12 or IO19

          +- VBAT pin up to 36V, and OUTA or OUTB will be on/off when you digitalWrite it high or low

             - IO12 = CTRL1

          -  - IO19 = CTRL2 - chip is not soldered by default 

          +  - IO19 = CTRL2 

             - IO13 = STATUS1

          -

             - IO18 = STATUS2

          @@ -57,6 +59,7 @@ https://www.electrodragon.com/product/esp32-can-rs-485-wire-interface-shield/

           ## ref

           - code please refer to our ESP32 arduino github repository 

          +- https://github.com/Edragon/Arduino-ESP32/tree/master/BSP/NWI1245/power-switch-test

           - https://github.com/Edragon/Arduino-ESP32

           - https://github.com/Edragon/Arduino-ESP32/blob/master/Sketchbook/interface/RS485-1/RS485-1.ino

...	...	@@ -23,6 +23,8 @@
23	23	### DAS
24	24	- [[DAS1033-DAT]] - [[DAS1043-DAT]] - [[DAS1087-DAT]]
25	25
	26	+- [[DAS1069-dat]]
	27	+
26	28	### DAR
27	29	- [[DAR1053-DAT]] - [[DAR1064-DAT]] - [[DAR1019-dat]]
28	30

...	...	@@ -28,10 +28,12 @@ https://www.electrodragon.com/product/esp32-can-rs-485-wire-interface-shield/
28	28	- IO5 = LED
29	29
30	30	- general load switching
	31	+- please note one chip is not soldering default in case you don't need two to save cost
	32	+- try IO12 or IO19
	33	+- VBAT pin up to 36V, and OUTA or OUTB will be on/off when you digitalWrite it high or low
31	34	- IO12 = CTRL1
32		- - IO19 = CTRL2 - chip is not soldered by default
	35	+ - IO19 = CTRL2
33	36	- IO13 = STATUS1
34		-
35	37	- IO18 = STATUS2
36	38
37	39
...	...	@@ -57,6 +59,7 @@ https://www.electrodragon.com/product/esp32-can-rs-485-wire-interface-shield/
57	59
58	60	## ref
59	61	- code please refer to our ESP32 arduino github repository
	62	+- https://github.com/Edragon/Arduino-ESP32/tree/master/BSP/NWI1245/power-switch-test
60	63	- https://github.com/Edragon/Arduino-ESP32
61	64	- https://github.com/Edragon/Arduino-ESP32/blob/master/Sketchbook/interface/RS485-1/RS485-1.ino
62	65