Changes in f4ade94: 1022

				Board/NBL/NBL1012-dat/NBL1012-dat.md
			
          @@ -0,0 +1,4 @@

          +

          +# NBL1012-dat 

          +

          +- [legacy wiki page.](https://w.electrodragon.com/w/BK3231)

          \ No newline at end of file

				Board/NBL/NBL1022-dat/2023-10-19-13-23-35.png
			
          Binary files /dev/null and b/Board/NBL/NBL1022-dat/2023-10-19-13-23-35.png differ

				Board/NBL/NBL1022-dat/2023-10-19-13-27-25.png
			
          Binary files /dev/null and b/Board/NBL/NBL1022-dat/2023-10-19-13-27-25.png differ

				Board/NBL/NBL1022-dat/NBL1022-dat.md
			
          @@ -0,0 +1,21 @@

          +# NBL1022-dat

          +

          +- [legacy wiki page](https://w.electrodragon.com/w/Category:BC-04)

          +

          +## Base Board Pin Definitions

          +

          +![](2023-10-19-13-27-25.png)

          +

          +## Backside Jumper Setup Mode:

          +

          +![](2023-10-19-13-23-35.png)

          +

          +Bottom jumper set hardware / software method for slave / master mode, Default setup for hardware method.

          +

          +| Jumper | Function         | Mode                      | Default |

          +| ------ | ---------------- | ------------------------- | ------- |

          +| SJ2    | master / slave   | hardware control M/S mode |

          +| SJ1    | soft / hard Mode | control mode select       | Hard    |

          +

          +- Top jumper set for slave / master mode.

          +- If you prefer to use software method by AT commands to change slave / mater mode, cut the bottom jumper connection (GND - middle pin), then re-connect to top by solder (VCC-middle pin).

...	...	@@ -0,0 +1,4 @@
	1	+
	2	+# NBL1012-dat
	3	+
	4	+- [legacy wiki page.](https://w.electrodragon.com/w/BK3231)
...	...	\ No newline at end of file

...	...	@@ -0,0 +1,21 @@
	1	+# NBL1022-dat
	2	+
	3	+- [legacy wiki page](https://w.electrodragon.com/w/Category:BC-04)
	4	+
	5	+## Base Board Pin Definitions
	6	+
	7	+![](2023-10-19-13-27-25.png)
	8	+
	9	+## Backside Jumper Setup Mode:
	10	+
	11	+![](2023-10-19-13-23-35.png)
	12	+
	13	+Bottom jumper set hardware / software method for slave / master mode, Default setup for hardware method.
	14	+
	15	+\| Jumper \| Function \| Mode \| Default \|
	16	+\| ------ \| ---------------- \| ------------------------- \| ------- \|
	17	+\| SJ2 \| master / slave \| hardware control M/S mode \|
	18	+\| SJ1 \| soft / hard Mode \| control mode select \| Hard \|
	19	+
	20	+- Top jumper set for slave / master mode.
	21	+- If you prefer to use software method by AT commands to change slave / mater mode, cut the bottom jumper connection (GND - middle pin), then re-connect to top by solder (VCC-middle pin).