Changes in d364a9d: nbl

				Board-dat/ILC/ILC1007-dat/ILC1007-dat.md
			
          @@ -1,4 +1,11 @@

           # ILC1007-dat

          -legacy wiki page - https://www.electrodragon.com/w/12864min_LCD

          \ No newline at end of file

          +legacy wiki page - https://www.electrodragon.com/w/12864min_LCD

          +

          +- [[ILC1008-dat]]

          +

          +

          +## ref 

          +

          +- [[ILC1007]]

          \ No newline at end of file

				Board-dat/NBL/NBL1018-dat/2023-10-19-13-52-14.png
			
          Binary files /dev/null and b/Board-dat/NBL/NBL1018-dat/2023-10-19-13-52-14.png differ

				Board-dat/NBL/NBL1018-dat/NBL1018-dat.md
			
          @@ -3,6 +3,29 @@

           https://www.electrodragon.com/product/30ft-3-3vdc-wireless-bluetooth-rf-transceiver-module-rs232-ttl/

          +## Features:

          +

          +- BQB certificated

          +- Master / Slave Mode supported

          +- classic bluetooth easy to use

          +

          +## Compare

          +

          +![](2023-10-19-13-52-14.png)

          +

          +| func                               | BC04—B         | HC—05            | HC—06          |

          +| ---------------------------------- | -------------- | ---------------- | -------------- |

          +| 1. Software master-slave setting   | ✔              | ✔                | ✔              |

          +| 2． Hardware master-slave settings | ✔              | X                | X              |

          +| 3． Ultra-low power consumption    | 2 ~ 10mA       | 30 ~ 40mA        | 30 ~ 40mA      |

          +| 4. Intelligent AT command system   | ✔              | X                | X              |

          +| 5． Normal AT set                  | ✔              | ✔                | ✔              |

          +| 6. Support help command            | ✔              | X                | X              |

          +| 7． Product Grade                  | Military Grade | Industrial Grade | Civilian Grade |

          +| 8． Support software development   | ✔              | X                | X              |

          +| 9. Support uplink command          | ✔              | X                | X              |

          +

          +

           ## Note 

          @@ -14,6 +37,9 @@ https://www.electrodragon.com/product/30ft-3-3vdc-wireless-bluetooth-rf-transcei

           ## ref 

          +simialr modules - [[BC04-B-dat]] - [[HC05-dat]] - [[HC06-dat]] - [[NBL1012-dat]]

          +

          +

           - [[BC04-B-dat]]

           - [[NBL1018]]

          \ No newline at end of file

				Board-dat/NBL/NBL1022-dat/2023-10-19-13-52-14.png
			
          Binary files a/Board-dat/NBL/NBL1022-dat/2023-10-19-13-52-14.png and /dev/null differ

				Board-dat/NBL/NBL1022-dat/2023-10-20-17-05-57.png
			
          Binary files a/Board-dat/NBL/NBL1022-dat/2023-10-20-17-05-57.png and /dev/null differ

				Board-dat/NBL/NBL1022-dat/2023-10-23-15-06-05.png
			
          Binary files a/Board-dat/NBL/NBL1022-dat/2023-10-23-15-06-05.png and /dev/null differ

				Board-dat/NBL/NBL1022-dat/NBL1022-dat.md
			
          @@ -4,79 +4,16 @@

           https://www.electrodragon.com/product/lc-05-bluetooth-serial-moduel-masterslave-in-one/

          -## Features:

          +This is a combination board of [[NBL1057-dat]] and [[NBL1018-dat]], please read their documentation seperataly. 

          -- BQB certificated

          -- Master / Slave Mode supported

          -- classic bluetooth easy to use

          -

          -## SCH

          -

          -![](2023-10-20-17-05-57.png)

          -

          -![](2023-10-23-15-06-05.png)

          -

          -## Base Board Pin Definitions

          -

          -![](2023-10-19-13-27-25.png)

          -

          -from left to right from front side

          -

          -- GND

          -- +5V

          -- 3V3

          -- TXD

          -- RXD

          -- Clear - clear the pairing status

          -

          -## Backside Jumper Setup Mode:

          -

          -![](2023-10-19-13-23-35.png)

          -

          -Bottom jumper set hardware / software method for slave / master mode, Default setup for hardware method.

          -

          -| Jumper | Function         | Mode                      | Default |

          -| ------ | ---------------- | ------------------------- | ------- |

          -| SJ2    | master / slave   | hardware control M/S mode |

          -| SJ1    | soft / hard Mode | control mode select       | Hard    |

          -

          -- Top jumper set for slave / master mode.

          -- If you prefer to use software method by AT commands to change slave / mater mode, cut the bottom jumper connection (GND - middle pin), then re-connect to top by solder (VCC-middle pin).

          -

          -## Note

          -

          -Wiring

          -

          -- Board RXD -> target RXD, board TXD -> target TXD

          -

          -Mode

          -

          -- Be aware default setting of the product is slave mode, communication only available between master and slave mode, but not master and master, or slave and slave mode.

           ## Demo Video

           - [Please see here.](https://www.youtube.com/watch?v=CmMGhHMciu8)

          -## Compare

          -

          -![](2023-10-19-13-52-14.png)

          -

          -| func                               | BC04—B         | HC—05            | HC—06          |

          -| ---------------------------------- | -------------- | ---------------- | -------------- |

          -| 1. Software master-slave setting   | ✔              | ✔                | ✔              |

          -| 2． Hardware master-slave settings | ✔              | X                | X              |

          -| 3． Ultra-low power consumption    | 2 ~ 10mA       | 30 ~ 40mA        | 30 ~ 40mA      |

          -| 4. Intelligent AT command system   | ✔              | X                | X              |

          -| 5． Normal AT set                  | ✔              | ✔                | ✔              |

          -| 6. Support help command            | ✔              | X                | X              |

          -| 7． Product Grade                  | Military Grade | Industrial Grade | Civilian Grade |

          -| 8． Support software development   | ✔              | X                | X              |

          -| 9. Support uplink command          | ✔              | X                | X              |

           ## ref

           - based on module - [[NBL1018-dat]] - [[NBL1022-dat]] - [[NBL1057-dat]]

          -simialr modules - [[BC04-B-dat]] - [[HC05-dat]] - [[HC06-dat]] - [[NBL1012-dat]]

          -

           - [[NBL1022]]

				Board-dat/NBL/NBL1057-dat/2023-10-20-17-05-57.png
			
          Binary files /dev/null and b/Board-dat/NBL/NBL1057-dat/2023-10-20-17-05-57.png differ

				Board-dat/NBL/NBL1057-dat/2023-10-23-15-06-05.png
			
          Binary files /dev/null and b/Board-dat/NBL/NBL1057-dat/2023-10-23-15-06-05.png differ

				Board-dat/NBL/NBL1057-dat/NBL1057-dat.md
			
          @@ -18,9 +18,38 @@ And customize Setup

           - state or status: pair state or AT commands status

          +## Base Board Pin Definitions

          +

          +![](2023-10-19-13-27-25.png)

          +

          +from left to right from front side

          +

          +- GND

          +- +5V

          +- 3V3

          +- TXD

          +- RXD

          +- Clear - clear the pairing status

          +

          +## Backside Jumper Setup Mode:

          +

          +![](2023-10-19-13-23-35.png)

          +

          +Bottom jumper set hardware / software method for slave / master mode, Default setup for hardware method.

          +

          +| Jumper | Function         | Mode                      | Default |

          +| ------ | ---------------- | ------------------------- | ------- |

          +| SJ2    | master / slave   | hardware control M/S mode |

          +| SJ1    | soft / hard Mode | control mode select       | Hard    |

          +

          +- Top jumper set for slave / master mode.

          +- If you prefer to use software method by AT commands to change slave / mater mode, cut the bottom jumper connection (GND - middle pin), then re-connect to top by solder (VCC-middle pin).

          +

          +

          +

           ## SCH

          -Version New 2

          +### Version New 2

           ![](2023-10-27-15-17-54.png)

          @@ -30,7 +59,7 @@ Version New 2

          -Version Old 1

          +### Version Old 1

           ![](2023-10-27-14-56-16.png)

          @@ -38,6 +67,22 @@ Version Old 1

           - default is software on.

           - To use hardware select, need cut off connection on software ON with middle pin first.

          +### base version 

          +

          +![](2023-10-20-17-05-57.png)

          +

          +![](2023-10-23-15-06-05.png)

          +

          +

          +## Wiring

          +

          +- Board RXD -> target RXD, board TXD -> target TXD

          +

          +## Mode

          +

          +- Be aware default setting of the product is slave mode, communication only available between master and slave mode, but not master and master, or slave and slave mode.

          +

          +

           ## ref

           - based on module - [[NBL1018-dat]] - [[NBL1022-dat]] - [[NBL1057-dat]]

...	...	@@ -1,4 +1,11 @@
1	1
2	2	# ILC1007-dat
3	3
4		-legacy wiki page - https://www.electrodragon.com/w/12864min_LCD
...	...	\ No newline at end of file
	0	+legacy wiki page - https://www.electrodragon.com/w/12864min_LCD
	1	+
	2	+- [[ILC1008-dat]]
	3	+
	4	+
	5	+## ref
	6	+
	7	+- [[ILC1007]]
...	...	\ No newline at end of file

...	...	@@ -3,6 +3,29 @@
3	3
4	4	https://www.electrodragon.com/product/30ft-3-3vdc-wireless-bluetooth-rf-transceiver-module-rs232-ttl/
5	5
	6	+## Features:
	7	+
	8	+- BQB certificated
	9	+- Master / Slave Mode supported
	10	+- classic bluetooth easy to use
	11	+
	12	+## Compare
	13	+
	14	+![](2023-10-19-13-52-14.png)
	15	+
	16	+\| func \| BC04—B \| HC—05 \| HC—06 \|
	17	+\| ---------------------------------- \| -------------- \| ---------------- \| -------------- \|
	18	+\| 1. Software master-slave setting \| ✔ \| ✔ \| ✔ \|
	19	+\| 2． Hardware master-slave settings \| ✔ \| X \| X \|
	20	+\| 3． Ultra-low power consumption \| 2 ~ 10mA \| 30 ~ 40mA \| 30 ~ 40mA \|
	21	+\| 4. Intelligent AT command system \| ✔ \| X \| X \|
	22	+\| 5． Normal AT set \| ✔ \| ✔ \| ✔ \|
	23	+\| 6. Support help command \| ✔ \| X \| X \|
	24	+\| 7． Product Grade \| Military Grade \| Industrial Grade \| Civilian Grade \|
	25	+\| 8． Support software development \| ✔ \| X \| X \|
	26	+\| 9. Support uplink command \| ✔ \| X \| X \|
	27	+
	28	+
6	29
7	30	## Note
8	31
...	...	@@ -14,6 +37,9 @@ https://www.electrodragon.com/product/30ft-3-3vdc-wireless-bluetooth-rf-transcei
14	37
15	38	## ref
16	39
	40	+simialr modules - [[BC04-B-dat]] - [[HC05-dat]] - [[HC06-dat]] - [[NBL1012-dat]]
	41	+
	42	+
17	43	- [[BC04-B-dat]]
18	44
19	45	- [[NBL1018]]
...	...	\ No newline at end of file

...	...	@@ -4,79 +4,16 @@
4	4
5	5	https://www.electrodragon.com/product/lc-05-bluetooth-serial-moduel-masterslave-in-one/
6	6
7		-## Features:
	7	+This is a combination board of [[NBL1057-dat]] and [[NBL1018-dat]], please read their documentation seperataly.
8	8
9		-- BQB certificated
10		-- Master / Slave Mode supported
11		-- classic bluetooth easy to use
12		-
13		-## SCH
14		-
15		-![](2023-10-20-17-05-57.png)
16		-
17		-![](2023-10-23-15-06-05.png)
18		-
19		-## Base Board Pin Definitions
20		-
21		-![](2023-10-19-13-27-25.png)
22		-
23		-from left to right from front side
24		-
25		-- GND
26		-- +5V
27		-- 3V3
28		-- TXD
29		-- RXD
30		-- Clear - clear the pairing status
31		-
32		-## Backside Jumper Setup Mode:
33		-
34		-![](2023-10-19-13-23-35.png)
35		-
36		-Bottom jumper set hardware / software method for slave / master mode, Default setup for hardware method.
37		-
38		-\| Jumper \| Function \| Mode \| Default \|
39		-\| ------ \| ---------------- \| ------------------------- \| ------- \|
40		-\| SJ2 \| master / slave \| hardware control M/S mode \|
41		-\| SJ1 \| soft / hard Mode \| control mode select \| Hard \|
42		-
43		-- Top jumper set for slave / master mode.
44		-- If you prefer to use software method by AT commands to change slave / mater mode, cut the bottom jumper connection (GND - middle pin), then re-connect to top by solder (VCC-middle pin).
45		-
46		-## Note
47		-
48		-Wiring
49		-
50		-- Board RXD -> target RXD, board TXD -> target TXD
51		-
52		-Mode
53		-
54		-- Be aware default setting of the product is slave mode, communication only available between master and slave mode, but not master and master, or slave and slave mode.
55	9
56	10	## Demo Video
57	11
58	12	- [Please see here.](https://www.youtube.com/watch?v=CmMGhHMciu8)
59	13
60		-## Compare
61		-
62		-![](2023-10-19-13-52-14.png)
63		-
64		-\| func \| BC04—B \| HC—05 \| HC—06 \|
65		-\| ---------------------------------- \| -------------- \| ---------------- \| -------------- \|
66		-\| 1. Software master-slave setting \| ✔ \| ✔ \| ✔ \|
67		-\| 2． Hardware master-slave settings \| ✔ \| X \| X \|
68		-\| 3． Ultra-low power consumption \| 2 ~ 10mA \| 30 ~ 40mA \| 30 ~ 40mA \|
69		-\| 4. Intelligent AT command system \| ✔ \| X \| X \|
70		-\| 5． Normal AT set \| ✔ \| ✔ \| ✔ \|
71		-\| 6. Support help command \| ✔ \| X \| X \|
72		-\| 7． Product Grade \| Military Grade \| Industrial Grade \| Civilian Grade \|
73		-\| 8． Support software development \| ✔ \| X \| X \|
74		-\| 9. Support uplink command \| ✔ \| X \| X \|
75	14
76	15	## ref
77	16
78	17	- based on module - [[NBL1018-dat]] - [[NBL1022-dat]] - [[NBL1057-dat]]
79	18
80		-simialr modules - [[BC04-B-dat]] - [[HC05-dat]] - [[HC06-dat]] - [[NBL1012-dat]]
81		-
82	19	- [[NBL1022]]

...	...	@@ -18,9 +18,38 @@ And customize Setup
18	18	- state or status: pair state or AT commands status
19	19
20	20
	21	+## Base Board Pin Definitions
	22	+
	23	+![](2023-10-19-13-27-25.png)
	24	+
	25	+from left to right from front side
	26	+
	27	+- GND
	28	+- +5V
	29	+- 3V3
	30	+- TXD
	31	+- RXD
	32	+- Clear - clear the pairing status
	33	+
	34	+## Backside Jumper Setup Mode:
	35	+
	36	+![](2023-10-19-13-23-35.png)
	37	+
	38	+Bottom jumper set hardware / software method for slave / master mode, Default setup for hardware method.
	39	+
	40	+\| Jumper \| Function \| Mode \| Default \|
	41	+\| ------ \| ---------------- \| ------------------------- \| ------- \|
	42	+\| SJ2 \| master / slave \| hardware control M/S mode \|
	43	+\| SJ1 \| soft / hard Mode \| control mode select \| Hard \|
	44	+
	45	+- Top jumper set for slave / master mode.
	46	+- If you prefer to use software method by AT commands to change slave / mater mode, cut the bottom jumper connection (GND - middle pin), then re-connect to top by solder (VCC-middle pin).
	47	+
	48	+
	49	+
21	50	## SCH
22	51
23		-Version New 2
	52	+### Version New 2
24	53
25	54	![](2023-10-27-15-17-54.png)
26	55
...	...	@@ -30,7 +59,7 @@ Version New 2
30	59
31	60
32	61
33		-Version Old 1
	62	+### Version Old 1
34	63
35	64	![](2023-10-27-14-56-16.png)
36	65
...	...	@@ -38,6 +67,22 @@ Version Old 1
38	67	- default is software on.
39	68	- To use hardware select, need cut off connection on software ON with middle pin first.
40	69
	70	+### base version
	71	+
	72	+![](2023-10-20-17-05-57.png)
	73	+
	74	+![](2023-10-23-15-06-05.png)
	75	+
	76	+
	77	+## Wiring
	78	+
	79	+- Board RXD -> target RXD, board TXD -> target TXD
	80	+
	81	+## Mode
	82	+
	83	+- Be aware default setting of the product is slave mode, communication only available between master and slave mode, but not master and master, or slave and slave mode.
	84	+
	85	+
41	86	## ref
42	87
43	88	- based on module - [[NBL1018-dat]] - [[NBL1022-dat]] - [[NBL1057-dat]]