Board-dat/DOD/DOD1096-dat/2024-10-25-19-14-08.png
... ...
Binary files /dev/null and b/Board-dat/DOD/DOD1096-dat/2024-10-25-19-14-08.png differ
Board-dat/DOD/DOD1096-dat/DOD1096-dat.md
... ...
@@ -25,6 +25,14 @@ STM32F411 开发板
25 25
- 128 Kbytes of SRAM
26 26
27 27
28
+## schematic
29
+
30
+![](2024-10-25-19-14-08.png)
31
+
32
+## SDK
33
+
34
+the board is [[micropython-dat]] compatible, load in firmware/bootloader
35
+
28 36
## ref
29 37
30 38
Chip-dat/ST-dat/STM32-dat/STM32F401-dat/STM32F401-dat.md
... ...
@@ -1,6 +1,42 @@
1 1
2 2
# STM32F401-dat
3 3
4
+
5
+## Demo Code And Reference Link
6
+
7
+* https://github.com/mcauser/WEACT_F411CEU6
8
+* Firmware Github private
9
+* https://github.com/Edragon/STM32F4_MP-TPY
10
+* https://github.com/Edragon/STM32F4_MP2
11
+
12
+
13
+Demo Test for accelerator - facebook dead, please visit at our youtube
14
+
15
+* https://fb.watch/bf5FTk2XWO/
16
+
17
+
18
+
19
+
20
+## More Notes
21
+
22
+* Use devices delete and pop out devices safely option in windows
23
+* reconnect USB cable and device to fully reload code
24
+
25
+
26
+
27
+## Other Similar Boards
28
+
29
+* ISOCORE
30
+* TYP_Board
31
+
32
+
33
+## more schematic
34
+
35
+- https://w.electrodragon.com/w/Category:STM32F4_HDK
36
+
37
+
4 38
## ref
5 39
40
+- [[micropython-dat]]
41
+
6 42
- [[STM32-dat]]
... ...
\ No newline at end of file
SDK-dat/AVR-dat/avrdude-dat/avrdude-dat.md
... ...
@@ -131,4 +131,11 @@ full commands by arduino IDE, this will be failed if use alone
131 131
132 132
![](2023-09-12-17-52-25.png)
133 133
134
+
135
+
136
+## ref
137
+
138
+- [[avr-dat]]
139
+
140
+
134 141
- [[avrdude]]
... ...
\ No newline at end of file
SDK-dat/microPython/micropython-dat.md
... ...
@@ -1,10 +1,10 @@
1 1
2 2
# micropython dat
3 3
4
-https://github.com/Edragon/Code-MicroPython
5
-https://github.com/Edragon/STM32-F4-MicroPython2
6
-
4
+- https://github.com/Edragon/Code-MicroPython
5
+- https://github.com/Edragon/STM32-F4-MicroPython2
7 6
7
+legacy wiki page - https://w.electrodragon.com/w/Micropython_Guide
8 8
9 9
## About micropython:
10 10
... ...
@@ -17,4 +17,26 @@ Open the USB flash drive, edit the main.py file, click Save, and reset the MCU t
17 17
18 18
![](2024-10-08-17-35-01.png)
19 19
20
-![](2024-10-08-17-35-13.png)
... ...
\ No newline at end of file
0
+![](2024-10-08-17-35-13.png)
1
+
2
+
3
+
4
+## Micropython Firmware / Bootloader
5
+
6
+For STM32F405RGT
7
+
8
+* Upload firmware hex by ST-link, no need reset pin
9
+* Flash Firmware - TPYBoardV102.hex
10
+
11
+* Reboot board and connect by USB, it will format itself, two LEDs ON, this takes 3-5 seconds
12
+
13
+* after this, U-disk will show up and sequential LED blink.
14
+
15
+* Now can upload new sketch into it.
16
+
17
+
18
+## compatible boards
19
+
20
+- [[STM32F401-dat]]
21
+
22
+- [[DOD1096-dat]]