Board-dat/MPC/MPC1073-DAT/MPC1073-DAT.md
... ...
@@ -82,7 +82,7 @@ optionally disable: audio in kernel
82 82
83 83
by following up setup, the GPIO output should be all good
84 84
85
-Start first with P0 Chain Test and standard demo code command line test
85
+Double check all the wirings are correct, and start first with P0 chain test using simple commandlines run
86 86
87 87
## demo video
88 88
Board-dat/OPM/OPM1070-dat/2025-02-03-15-19-17.png
... ...
Binary files /dev/null and b/Board-dat/OPM/OPM1070-dat/2025-02-03-15-19-17.png differ
Board-dat/OPM/OPM1070-dat/2025-02-03-15-23-09.png
... ...
Binary files /dev/null and b/Board-dat/OPM/OPM1070-dat/2025-02-03-15-23-09.png differ
Board-dat/OPM/OPM1070-dat/OPM1070-dat.md
... ...
@@ -1,4 +1,44 @@
1 1
2 2
# OPM1070-dat
3 3
4
+## Specs
5
+
6
+- Working temperature (°C) Normal conditions meet the following figure derating -25°~+70°
7
+- Working humidity (RH) 20-90%, no condensation
8
+- Temperature drift coefficient ±0.02%/°C
9
+- Storage temperature and humidity -40~+85°C 10-95%RH
10
+- Switching frequency (KHz) 65
11
+- Insulation voltage (VAC) input to output, test 605, ≤5mA3000VAC
12
+- Insulation resistance (MQ) input to output, 500VDC 100
13
+- Leakage current (mA) 500VDC input to output ≤0.25m A/RMS value
14
+- MTBF@25°C (MIL-HDBK-217F)>215000h
15
+- Safety level adaptation: CLASS B
16
+- Vibration resistance 110-500Hz2G10 minutes/cycle.X, Y, Z 60 minutes each
17
+
18
+- Electromagnetic compatibility
19
+ - ! Comply with: IEC62368-1/IEC61558-1ClassB
20
+ - Lightning strike: differential mode 2KV, IEC61000-4-2ClassB, common mode: 2KV, IEC61000-4-2ClaSsB.
21
+
22
+Note
23
+
24
+1. Unless otherwise specified, all specifications are measured at an input of 230vaC, rated load, and an ambient temperature of 25°C;
25
+2. Ripple and noise measurement method: use a 12" twisted pair cable, and connect a 0.1uF capacitor in parallel to the terminal, and measure at a bandwidth of 20MHz;
26
+3. Accuracy: includes the shear error, linear regulation rate, and load regulation rate;
27
+4. The power supply should be regarded as part of the components in the system, and electromagnetic compatibility related confirmation should be carried out in conjunction with the terminal equipment;
28
+5. The output needs to be reduced under low input voltage. Please refer to the reduction curve for details;
29
+
30
+
31
+### Dimension
32
+
33
+![](2025-02-03-15-19-17.png)
34
+
35
+### Module Electric Features
36
+
37
+![](2025-02-03-15-23-09.png)
38
+
39
+
40
+## ref
41
+
42
+- [[ACDC-dat]]
43
+
4 44
- [[OPM1070]]
... ...
\ No newline at end of file
Tech-dat/power-dat/AC-Mains-dat/ACDC-dat/2025-02-03-15-20-49.png
... ...
Binary files /dev/null and b/Tech-dat/power-dat/AC-Mains-dat/ACDC-dat/2025-02-03-15-20-49.png differ
Tech-dat/power-dat/AC-Mains-dat/ACDC-dat/2025-02-03-15-21-51.png
... ...
Binary files /dev/null and b/Tech-dat/power-dat/AC-Mains-dat/ACDC-dat/2025-02-03-15-21-51.png differ
Tech-dat/power-dat/AC-Mains-dat/ACDC-dat/ACDC-dat.md
... ...
@@ -14,7 +14,27 @@
14 14
- [[AP8022-dat]] - [[AP8012-dat]]
15 15
16 16
17
+## Board Function diagram
17 18
19
+![](2025-02-03-15-20-49.png)
20
+
21
+- Power supply principle scheme block diagram
22
+- Mains power 220VAC
23
+- Electromagnetic interference filter
24
+- Rectification and filtering
25
+- Low voltage rectifier filter
26
+- DC output
27
+- Output detection
28
+- Power detection
29
+- PWM switch control
30
+- Temperature detection
31
+- Signal comprehensive analysis/processing
32
+- feedback control
33
+
34
+
35
+## Usage Applciation
36
+
37
+![](2025-02-03-15-21-51.png)
18 38
19 39
## peripheral SCH
20 40