3e535f03cae3334444fd5b84dd3c3be57bab2e57
Board-dat/NBL/NBL1107-dat/NBL1107-dat.md
| ... | ... | @@ -11,6 +11,29 @@ legacy wiki page - https://w.electrodragon.com/w/Mesh-Node |
| 11 | 11 | |
| 12 | 12 | - SJ1 setup button output to either Reset or P32 |
| 13 | 13 | |
| 14 | +## Pin Definitiosn |
|
| 15 | + |
|
| 16 | +| MCU pins | BT Modules | Sensors | Other | |
|
| 17 | +| ---------- | ---------- | ---------- | -------------------- | |
|
| 18 | +| Reset | | | Button Reset or PROG | |
|
| 19 | +| U0_TXD | BT_RXD | | | |
|
| 20 | +| U0_RXD | BT_TXD | | | |
|
| 21 | +| P03 | - | - | NC | |
|
| 22 | +| P15 | BT_IN2 | | | |
|
| 23 | +| P14 | BT_IN1 | | | |
|
| 24 | +| P23 | BT_stat | | | |
|
| 25 | +| P24 | | | Button Alternative | |
|
| 26 | +| P25 | | Sensor SDA | | |
|
| 27 | +| P26 | | Sensor SCL | | |
|
| 28 | +| P27 | | | lead out free | |
|
| 29 | +| P31 | | | lead out free | |
|
| 30 | +| P32 | BT_PWRC | | | |
|
| 31 | +| P33 | | | Bat_ADC | |
|
| 32 | +| P34 | | | Relay | |
|
| 33 | +| P35_U1_TXD | | | free or PROG | |
|
| 34 | +| P36_U1_RXD | | | free or PROG | |
|
| 35 | + |
|
| 36 | + |
|
| 14 | 37 | |
| 15 | 38 | ## ref |
| 16 | 39 |
Chip-cn-dat/JDY-dat/JDY-25M-dat/JDY-25M-dat.md
| ... | ... | @@ -9,8 +9,43 @@ legacy wiki page - https://www.electrodragon.com/w/JDY-25M |
| 9 | 9 | |
| 10 | 10 |  |
| 11 | 11 | |
| 12 | -- [[NBL1101-dat]] |
|
| 12 | +- [[NBL1101-dat]] - [[NBL1107-dat]] |
|
| 13 | 13 | |
| 14 | +## Pins |
|
| 15 | + |
|
| 16 | +| Pin | Definition | Function | Description | |
|
| 17 | +| --- | ---------- | ------------------------ | ------------------------------------------------------------- | |
|
| 18 | +| 1 | TXD | Serial port | Serial output, the level is TTL level | |
|
| 19 | +| 2 | RXD | Serial port | Serial input, the level is TTL level | |
|
| 20 | +| 3 | NULL | Null | - | |
|
| 21 | +| 4 | NULL | Null | - | |
|
| 22 | +| 5 | KEY5 | Input 5 | inputs* | |
|
| 23 | +| 6 | KEY4 | Input 4 | inputs* | |
|
| 24 | +| 7 | KEY3 | Input 3 | inputs* | |
|
| 25 | +| 8 | KEY2 | Input 2 | inputs* | |
|
| 26 | +| 9 | NULL | Null | - | |
|
| 27 | +| 10 | KEY1 | Input 1 | inputs* | |
|
| 28 | +| 11 | RESET | Reset | Low level reset, high level working (high level if suspended) | |
|
| 29 | +| 12 | VCC | Power Supply | Supply（1.8-3.6V） | |
|
| 30 | +| 13 | GND | GND | Power ground | |
|
| 31 | +| 14 | PWRC | Sleep wake pin | PWRC descriptions* | |
|
| 32 | +| 15 | ALED | Broadcast LED indication | LED_status* | |
|
| 33 | +| 16 | STAT | Connection status | status* | |
|
| 34 | +| 17 | OUTPUT5 | Output 5 | outputs* | |
|
| 35 | +| 18 | NULL | Null | - | |
|
| 36 | +| 19 | NULL | Null | - | |
|
| 37 | +| 20 | NULL | Null | - | |
|
| 38 | +| 21 | NULL | Null | - | |
|
| 39 | +| 22 | OUTPUT1 | Output 1 | outputs* | |
|
| 40 | +| 23 | OUTPUT2 | Output 2 | outputs* | |
|
| 41 | +| 24 | OUTPUT3 | Output 3 | outputs* | |
|
| 42 | +| 25 | OUTPUT4 | Output 4 | outputs* | |
|
| 43 | + |
|
| 44 | +* outputs = Default low level, support serial instruction control and input KEY pin control in network state |
|
| 45 | +* status = In non mesh mode, low level if not connected, high level after connection In mesh mode (output high level if connect to network successfully, if not, output low level) |
|
| 46 | +* inputs = inputs |
|
| 47 | +* PWRC descriptions = Support PWRC pin wake-up in deep sleep state, and AT instruction sending is supported when the connection status is pulled down |
|
| 48 | +* LED_status = In non mesh mode (flash if not connected, light on after connection) |
|
| 14 | 49 | |
| 15 | 50 | ## AT commands |
| 16 | 51 |